For older model Astoria espresso machines. Also replaces the AS_60 lever piston o-ring style gasket. Very rarely used today, you are probably looking for the AS_56

A thicker gasket for older model Astoria espresso machines. Very rarely used today, you are probably looking for the AS_56. As a rule of thumb, Astoria stopped manufacturing the group head that accepts this gasket in 1995. You should make certain that this gaskets dimensions match the dimensions of your existing gasket. This is probably not it.

For newer model Astoria, Laurentis and Rio espresso machines.

This is for considerably older machines, and is not very commonly used today. For most models, such as the Portofino, the BF_11 is used. The BF_1 is used in older Brasilia models (and very rarely with Astoria).

Thick group head gasket used in Brasilia models with the twelve hole dispersion plate. 70 x 56 x 8mm

7mm thick La Cimbali flat group head gasket.

La Cimbali 7/9mm thick conical group head gasket.

Manufactured with a higher quality rubber to resist high temperatures better. Only one of these on hand, and then they are gone!

For a thinner gasket, use part P_23

With internal lateral cuts

Probably the most common group head gasket used today, the F_59 is used in some models of Brasilia, Bravo, ECM, Faema, Futurmat, Gaggia (Espagna - Italcrem), Isomac, La Pavoni, Sorrento, Vibiemme (VBM), VFA and Wega.If your portafilters are engaging too far to the right (and you don't want to buy new portafilters), you may want to consider purchasing the F_60, the 9mm gasket.Purchase 3 for $5.00 each, 6 for $4.50, 12 for $4.00 or 24 for $3.50 each!

The 9mm E-61 group head gasket is used with machines whose portafilters have worn so far that when engaged into the group head, they pull too far to the right from a six o'clock center position.

Same as F_59 and W_556_. This part IS NOT for the Grimac Espressione line, which we do not carry

This fits all commercial Gaggia equipment and most home models, but one should measure the height of the existing gasket from their really old Gaggia home machines, such as the Coffee and Espresso models, as they may have a much thinner gasket that unfortunately is unavailable from us

The 10mm group head gasket is used with machines whose portafilters have worn so far that when engaged into the group head, they pull too far to the right from a six o'clock center position.

72 x 55 x 7mm. Fits La Marzocco Linea, La Marzocco FB70

72 x 55 x 6/8mm. Fits La Marzocco Linea, La Marzocco FB70

72 x 55 x 6mm. Fits La Marzocco Linea, La Marzocco FB70

A softer version of the commercial gasket, direct from Rancilio. 74 x 57 x 8mm

Rancilio commercial group head gasket 72 x 57 x 8mm

For two, three and four group machines. For the single or one group units, use S98050001

6.5mm La Spaziale group head gasket 63 x 52 x 6.5

These are for the Nuova Simonelli Ellimatic and Beach models

Old style

New conical Nuova Simonelli group head gasket used in most commercial Simonelli commercial machines (Simonelli has discontinued the flat version), as well as the Oscar home model.For the Aurelia model, use S_418.The Ellimatic and Beach models use the S_1 gasket.

74 x 57 x 9 mm

This is the same as the F_59, but is made with a softer rubber. 73 x 57 x 8mm

8.5mm Group Head Gasket. Used when your portafilter gets worn and pulls too far (past a six o'clock position) to the right when engaged in the group head. 73 x 57 x 8.5mm

73 x 57 x 9mm